Altivar Process ATV600

Variable speed drive

Process and utilities

ATV630

Standard version

Synchronous motors
Asynchronous motors

Wall mount

Without EMC filter

IP21 conforming to IEC 61800-5-1
IP21 conforming to IEC 60529

UL type 1 conforming to UL 508C

Forced convection

50...60 Hz - 5...5 %

3 phases

200...240 V - 15...10 %

15 kW (normal duty)
11 kW (heavy duty)

20 hp normal duty
15 hp heavy duty

52.6 A at 200 V (normal duty)
45.5 A at 240 V (normal duty)
40.1 A at 200 V (heavy duty)
34.3 A at 240 V (heavy duty)

50 kA

18.9 kVA at 240 V (normal duty)
14.3 kVA at 240 V (heavy duty)

63.4 A at 4 kHz for normal duty
46.8 A at 4 kHz for heavy duty

69.7 A during 60 s (normal duty)
70.2 A during 60 s (heavy duty)

Variable torque standard
Constant torque standard
Optimized torque mode

Permanent magnet motor
Synchronous reluctance motor

0.0001…0.5 kHz

0.1…599 Hz

4 kHz

2...12 kHz adjustable
4...12 kHz with derating factor

STO (safe torque off) SIL 3

16 preset speeds

Ethernet
Modbus serial
Modbus TCP

Slot A: communication module, Profibus DP V1
Slot A: communication module, Profinet
Slot A: communication module, DeviceNet
Slot A: communication module, Modbus TCP/EtherNet/IP
Slot A: communication module, CANopen daisy chain RJ45
Slot A: communication module, CANopen SUB-D 9
Slot A: communication module, CANopen screw terminals
Slot A/slot B: digital and analog I/O extension module
Slot A/slot B: output relay extension module
Slot A: communication module, Ethernet IP/Modbus TCP/MD-Link
Communication module, BACnet MS/TP
Communication module, Ethernet Powerlink

<= power supply voltage

1.1 x In during 60 s (normal duty)
1.5 x In during 60 s (heavy duty)

Can be suppressed
Automatic whatever the load
Not available in permanent magnet motor law
Adjustable

Linear adjustable separately from 0.01...9999 s

By DC injection

Thermal protection: motor
Safe torque off: motor
Motor phase break: motor
Thermal protection: drive
Safe torque off: drive
Overheating: drive
Overcurrent between output phases and earth: drive
Overload of output voltage: drive
Short-circuit protection: drive
Motor phase break: drive
Overvoltages on the DC bus: drive
Line supply overvoltage: drive
Line supply undervoltage: drive
Line supply phase loss: drive
Overspeed: drive
Break on the control circuit: drive

Display unit: 0.1 Hz
Analog input: 0.012/50 Hz

Control: removable screw terminals0.5...1.5 mm²/AWG 20...AWG 16
Line side: screw terminal25...50 mm²/AWG 4...AWG 1
Motor: screw terminal25...50 mm²/AWG 4...AWG 1

RJ45 (on the remote graphic terminal) for Ethernet/Modbus TCP
RJ45 (on the remote graphic terminal) for Modbus serial

2-wire RS 485 for Modbus serial

RTU for Modbus serial

10/100 Mbit/s for Ethernet IP/Modbus TCP
4.8, 9.6, 19.2, 38.4 kbit/s for Modbus serial

Half duplex, full duplex, autonegotiation Ethernet/Modbus TCP

8 bits, configurable odd, even or no parity for Modbus serial

No impedance for Modbus serial

1…247 for Modbus serial

Slave Modbus TCP

External supply for digital inputs: 24 V DC (19…30 V), <1.25 mA, protection type: overload and short-circuit protection
Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 mA, protection type: overload and short-circuit protection
Internal supply for digital inputs and STO: 24 V DC (21…27 V), <200 mA, protection type: overload and short-circuit protection

3 LEDslocal diagnostic:
3 LEDs (dual colour)embedded communication status:
4 LEDs (dual colour)communication module status:
1 LED (red)presence of voltage:

226 mm

673 mm

271 mm

13.6 kg

3

AI1, AI2, AI3 software-configurable voltage: 0...10 V DC, impedance: 30 kOhm, resolution 12 bits
AI1, AI2, AI3 software-configurable current: 0...20 mA/4...20 mA, impedance: 250 Ohm, resolution 12 bits

8

DI1...DI6 programmable, 24 V DC (<= 30 V), impedance: 3.5 kOhm
DI5, DI6 programmable as pulse input: 0…30 kHz, 24 V DC (<= 30 V)
STOA, STOB safe torque off, 24 V DC (<= 30 V), impedance: > 2.2 kOhm

DI1...DI6: discrete input level 1 PLC conforming to EN/IEC 61131-2
DI5, DI6: discrete input level 1 PLC conforming to IEC 65A-68
STOA, STOB: discrete input level 1 PLC conforming to EN/IEC 61131-2

Positive logic (source) (DI1...DI6), < 5 V (state 0), > 11 V (state 1)
Negative logic (sink) (DI1...DI6), > 16 V (state 0), < 10 V (state 1)
Positive logic (source) (DI5, DI6), < 0.6 V (state 0), > 2.5 V (state 1)
Positive logic (source) (STOA, STOB), < 5 V (state 0), > 11 V (state 1)

2

Software-configurable voltage AO1, AO2: 0...10 V DC impedance 470 Ohm, resolution 10 bits
Software-configurable current AO1, AO2: 0...20 mA, resolution 10 bits

2 ms +/- 0.5 ms (DI1...DI4) - discrete input
5 ms +/- 1 ms (DI5, DI6) - discrete input
5 ms +/- 0.1 ms (AI1, AI2, AI3) - analog input
10 ms +/- 1 ms (AO1) - analog output

+/- 0.6 % AI1, AI2, AI3 for a temperature variation 60 °C analog input
+/- 1 % AO1, AO2 for a temperature variation 60 °C analog output

AI1, AI2, AI3: +/- 0.15 % of maximum value for analog input
AO1, AO2: +/- 0.2 % for analog output

3

Configurable relay logic R1: fault relay NO/NC electrical durability 100000 cycles
Configurable relay logic R2: sequence relay NO electrical durability 100000 cycles
Configurable relay logic R3: sequence relay NO electrical durability 100000 cycles

Relay output (R1, R2, R3): 5 ms (+/- 0.5 ms)

Relay output R1, R2, R3: 5 mA at 24 V DC

Relay output R1, R2, R3 on resistive load, cos phi = 1: 3 A at 250 V AC
Relay output R1, R2, R3 on resistive load, cos phi = 1: 3 A at 30 V DC
Relay output R1, R2, R3 on inductive load, cos phi = 0.4 and L/R = 7 ms: 2 A at 250 V AC
Relay output R1, R2, R3 on inductive load, cos phi = 0.4 and L/R = 7 ms: 2 A at 30 V DC

Between power and control terminals

Compressor centrifugal Building - HVAC
Other application Food and beverage processing
Fan Mining mineral and metal
Pump Mining mineral and metal
Fan Oil and gas
Other application Water and waste water
Screw compressor Building - HVAC
Pump Food and beverage processing
Fan Food and beverage processing
Atomization Food and beverage processing
Electro submersible pump (ESP) Oil and gas
Water injection pump Oil and gas
Jet fuel pump Oil and gas
Compressor for refinery Oil and gas
Centrifuge pump Water and waste water
Positive displacement pump Water and waste water
Electro submersible pump (ESP) Water and waste water
Screw pump Water and waste water
Lobe compressor Water and waste water
Screw compressor Water and waste water
Compressor centrifugal Water and waste water
Fan Water and waste water
Conveyor Water and waste water
Mixer Water and waste water

15…25 kW at 200…240 V 3 phases

> 1 MOhm 500 V DC for 1 minute to earth

63.5 dB conforming to 86/188/EEC

Natural convection: 87 W at 200 V, switching frequency 4 kHz
Forced convection: 486 W at 200 V, switching frequency 4 kHz

240 m3/h

Vertical +/- 10 degree

<48 % from 80...100 % of load conforming to IEC 61000-3-12

Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2
Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3
Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4
1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5
Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6

2 conforming to EN/IEC 61800-5-1

1.5 mm peak to peak (f= 2…13 Hz) conforming to IEC 60068-2-6
1 gn (f= 13…200 Hz) conforming to IEC 60068-2-6

15 gn for 11 ms conforming to IEC 60068-2-27

5…95 % without condensation conforming to IEC 60068-2-3

-15…50 °C (without)
50…60 °C (with derating factor)

-40…70 °C

<= 1000 m without
1000...4800 m with current derating 1 % per 100 m

Chemical pollution resistance class 3C3 conforming to EN/IEC 60721-3-3
Dust pollution resistance class 3S3 conforming to EN/IEC 60721-3-3

UL 508C
EN/IEC 61800-3
Environment 1 category C2 EN/IEC 61800-3
Environment 2 category C3 EN/IEC 61800-3
EN/IEC 61800-5-1
IEC 61000-3-12
IEC 60721-3
IEC 61508
IEC 13849-1

ATEX zone 2/22
TÜV
CSA
DNV-GL
UL
REACH
ATEX INERIS

CE

Green Premium product