Danh mục sản phẩm

Hỗ trợ trực tuyến

icon hotline

+84917.943.068

Hỗ trợ online
skyper

Icon điện thoại +84917.943.068

Icon email sales@tmpvietnam.com

VIDEO

Chi tiết sản phẩm

  • Bộ điều khiển tự động điều chỉnh canh biên AE1000 Nireco

  • Mã SP:
  • Giá : Liên hệ
  • Mã sản phẩm:AE1000

    Xuất sứ: Japan

    Liên hệ: 0917 943 068

    Email: sales@tmpvietnam.com

    Công Ty TNHH và DV Tăng Minh Phát là nhà phân phối chính thức của hãng NIRECO tại việt nam, chuyên cung cấp các thiết bị đo lường và phân tích khí độc hại hãng NIRECOtại Việt Nam, NIRECO Việt Nam

Overview

The Liteguide Controller AE1000 carries out EPC (Edge Position Control) through a combination of Photoheads (PH16B) and Ultrasonic Sensor (UH01), CPC (Center Position Control) through a combination of Photoheads and Autowide Sensor (AWE280 etc.) and LFC (Line Follower Control) through a combination of LH19 and LH110.

  • Liteguide Controller AE1000 is the successor to the previously well established AE900E and AE900L controllers.
  • This single type can be connected to Nireco standard sensors which has been used with the AE900E or AE900L controller.
    (Some sensors may need to be used with a preamp)
  • Can be used directly coupled with electrical actuators K12 and K61. Can also be connected to the K80 series through use of a driver.
  • Has 2 systems, a sensor input stage and a shift input stage, which can be switched for use.
  • Uses a larger LCD display than previous models with a white backlight making it both easier to see and allowing for verification of a greater amount of information.

process_ae1000_2nd.jpg

Power Supply Voltage AC100 to 240V 50/60Hz ±10%
Power Consumption 300 VA (inrush current 100 A 10 ms typical (200 V))
Power Fuse 250V AC, 3.15 A (time-lag type)
Ambient Operating Temperature 0 to 50°C
Ambient Operating Humidity 35 to 85% RH or lower (no condensation)
Vibration Resistance 3.5 mm, 1 G, 3 to 150 Hz, three-directions (1hour)
Power supply Noise 2.5 kVp-p, normal mode, common mode 50 ns, 1μs width
Usage atmosphere: Area with no water, flammable or corrosive gases, and little dust.
Mass Approximately 5 kg
IP Class IP30
Input 2 Sensor systems Voltage input Maximum ±5V(No input resistance)
Current input 0-20mA (input resistance converted to 240/2kΩ)
2 analog shift systems Voltage input Maximum ±10V
Centering Proximity switch input (0-8V, 1.2kΩ input resistance)(Applies to: KL1632. 0-90P)
Position Transmitter Voltage input Maximum ±10V
Photo coupler input 
(12V DC, 15mA)
Remote controller :
Operation mode switching(auto / manual / centering)
Operation keys (left / right / auto balance / reverse)
System selection(EPC1 / EPC2)
Locks 3 points
Actuator end limit :
2 points
Output Electrical actuator K12 ±24V DC, 1A(maximum) or K62 ±36V DC, 2A(maximum)
Lamp power source 4 to 12V DC, variable (maximum 1A)
Fine tuner, Position transmitter, LH8B ±5V power source (maximum 0.1A)
Sensors ±15V power source (+15V, 1A; -15V, 0.2A)
(Note: The current capacity on the + side combined with the lamp power source in(2) is less than 1A.)
Centering proximity switch power source 8V DC (maximum 30mA)
2 indicator systems Voltage output Maximum ±10V (load resistance 2kΩ or greater)
Deviation output
Position transmitter output
Photo coupler output 
(24V DC, 40mA)
Remote controller :
Operation mode state(auto / manual / centering)
System state (EPC1 / EPC2)
Alarms Excessive deviation
End limit
Actuator lock
Actuator excessive load

Sản phẩm cùng loại